Turn it clockwise to tighten the gap of the jaws for thinner material or counterclockwise to make the gap of the jaws larger for thicker material. Nibbler & Shear Accessories P&N QUICKBITS Nibbler Replacement Punch P&N QUICKBITS 1/4-Hex Drill/Impact Driver Sheet Metal Nibbler Attachment P&N QUICKBITS 1/. To adjust, locate the 3/16” set screw on the back of the tool, towards the front of the tool near the jaws. TSHD – The clearance between the cutting jaws is adjustable in order to achieve the optimum cut for thick or thin material. How do you adjust the tool to get the optimum cut? The tool will need to be adjusted when going from very thin to thick material and vice versa. This well tailored attachment quickly inserts into the chuck of a corded or cordless drill to make fast straight, curved or square cuts in most common sheet. TSHD – The Turboshear Sheet Metal Cutter will make clean cuts throughout the range of thicknesses of material listed above. The TSHD is also rated to cut 20-gauge (.82 mm) spiral duct work. 100 inch (2.55 mm) copper (metal roofing, gutters). TSHD – cuts 18-gauge (1.32 mm) galvanized steel (HVAC duct work, auto body panels), 20-gauge (.82 mm) non hardened carbon steel and stainless steel (metal roofing panels), 14-gauge (1.54 mm) aluminum (trim coil, flashing), and. The clamp collar allows the shear head to be rotated 360° and set in any position for optimum tool clearance when navigating profiles or to facilitate easy material flow. Optional spacers are stored on the clamp for large motor housings. The patented compact telescoping drill clamp adjusts to fit both length and width of popular drill sizes including smaller bodied impact drivers. Replacement blades are also available and can be easily installed on the job.Ī sleek, lightweight aluminum cast shear head and molded drill clamp allow maximum portability. However, the blades are much thicker & heavier than scissor blades to enables them to cut through sheet metal. The Straight-cut tin snips have straight blades that are slightly shorter than the length of the scissor blade. A lateral blade adjustment capability is included, which ensures that optimum cutting performance and maneuverability can be maintained for the life of the blades. The three commons types are straight-cut tin snips, offsets tin snips, and vertical tin snips. The heavy-duty hardened carbon steel blades of the tool offer up to 18-guage (1.22 mm) cutting capacity in mild steel. Or cut through layered metal and seams, even the ribs of spiral duct.Navigate crosscuts through profiles of metal building and roofing panels We’ll recommend a pair of tin snips that will get you through 90 percent of the jobs you’ll run into.With Malco’s TSHD Sheet Metal Cutter, you are able to easily: The shear’s wide-opening jaws can operate at high or low speeds for the control you need, when you need it. This electric shear attachment has the capability to make fast straight, curved, or square cuts in most common sheet metals. Replacement blades are also available and are easily installed on the job.The Malco TurboShear Heavy Duty (TSHD) is a powerful sheet metal cutting tool that can be quickly attached to a corded or cordless drill. A lateral blade adjustment capability ensures that optimum cutting performance and maneuverability can be maintained for the life of the blades. Heavy-duty gearing and beefy, hardened carbon steel blades combine to offer long service life in 30 to 24-gauge (0.31 – 0.61 mm) roofing panel metal. The shear can operate at high or low speeds for the control you need to follow a precise cut line. As these offset blades follow the rising angle of a corrugated or trapezoidal profile, the drill handle or battery pack has clearance to naturally tip downward and still clear the roofing panel surface. Elongated blades with compact jaws create a steep 75-degree offset so that the drill is held at a nearly vertical approach when starting a cut. This versatile and portable TurboShear fits a drill you already own to make easy cross cuts, fast lengthwise cuts, and precise circular and square outlet cuts in large or small pattern corrugated metal roofing and common trapezoidal (box) pattern metal roofing panels. Malco’s TSCM TurboShear works better and faster than manual metal roofing shears.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |